How to Upholster a Chair (DIY (2024)

ByCarmen De La Paz

Step 1

Removeseatfromchair

Remove the screws that secure the seat to the base of the chair or bench. Set the chair base aside while you work on the seat. Save the screws that came with the chair, asthey will be usedagain to put the chair back together.

TMB Studio

Step 2

Remove staples

With the seat bottom facing up, carefully work your way around the edgeremovingthe staples to release the cambric dust fabric and old upholstery fabric.Try to keep the dust cover material intactasyou may want to use it again.If the cambric fabric tears, you can replace it.Pull apart the fabric from the seat.

TMB Studio

Step 3

Cut new fabric

Cut the new fabric to size using the original upholstery material as a template.

If your fabric has alargerepetitive pattern, be conscious of choosing how you want it to look once the chair is right-side up.Also, be aware of the differences between the front and back orientation of the chair. Some chairs are not symmetrical, making it easy to lose track of the layout.Mark the front and back to help keep the pattern inthe direction you prefer.

• Pro tip:At this point, take a good look at the foam.If the foam in theold furnitureis worn and matted down, you may want to replace the foam and add new batting.The original foamis often reusedwhen reupholstering, but changing out the foam is always an option to consider.

TMB Studio

Step 4

Position new fabric andstaple

Position and center the new fabric on the seat, allowing approximately two inches to fold over and cover the seatcompletely.Make sure the fabricis pulledtaughtaround the edges of the chairwhile you staple.Work carefully, avoiding wrinkles and not overlapping the fabric.

• Position the fabric where you want it and pull it tightly on the seat.
• Place one staple in the middle of each side of the chair – this will prevent the fabric from shifting as you work your way around with the rest of the staples.
• Focus on one side at a time, gradually workingyour wayaround the chair.
• Use a small tack hammerto deeply seed the staples into the fabric and wood seat.
  • Pro tip: Apply some spray mount adhesive along the edges, catching the wood seat and the fabric so the edges stick and don’tshift around as you staple.

Important:

• DO NOT staple fabric in the corners until all four sidesare stapledin place.
• Cut away fabric to expose screw holes for the frame and seattocome together.Thiswill help you find the old screw holes easily and prevent the fabric from twisting when installing the screws.

Step 5

Upholstering chair corners

Corners are the trickiest because the fabric folds are bulky and hard to work with.These bulky folds may prevent the seat from sitting flatly against the framewhen you attach it back onto the chair. Feel free to cut away fabric as you fold the corners.

The most important part of thisupholstery repairproject is to ensure that the fabric covers the seatcompletelyand extends beyond where the frame will sit. Think of the corners as wrapping a gift — the fabric canbe trimmedas needed. Use as many staples asit takesto get the fabric to lay flat and secure.

TMB Studio

Step 6

Replace the cambricdustcover

Reposition the cambric dust cover and staple it in place.Avoid placing staples in the previous holesasthe fabric is weakened and may come aparteasily. If needed, use atackhammer to sink staples deeper.

TMB Studio

Step 7

Re-install upholstered seat

With the fabric fully secured, reposition the chair seat onto the frame and make sure it sits flat. Using the same screws, join the seat back into place.Be sure to enter the same holes so the seatis positionedcorrectly.

• Tip:If the screw holesare stripped, fill the holes with small pieces of toothpicks and a dab of wood glue. Then screw it in.

Paint an added feature:Toreallydress up the chair and add another pop of color, I picked a color complementary to the fabric and painted the lower third of the chair.Thisis called a“paint dip.”

TMB Studio

FAQs

Will any fabric work to reupholster a chair?

Yes and no.When selecting a fabric toupholster a cushionor seat, you want to check quality and durability.Go to a fabric store and look at recommended uses and fabric grades A through F.Fabric grades will reflect the price and quality of the fabric.An“A”grade is less expensive, with“FGrade”being the mostexpensivebecause it has a more complex weave and typically incorporates more natural materials.

Another way to determine the quality of a fabric is called a double rub.It is a test to determine how oftena fabric canbe rubbedbefore it wears out.One pass back and forth accounts for one“double rub.”Domestic fabricsare usually rated at 25,000 double-rubs. If you are purchasing one that is over 50,000 for a high-use chair, you will be making a good fabric choice.Industry standards set commercial-grade fabrics as wearing out after 100,000 to 250,000 double-rubs.Take your time to look at the differences before you make your final selection.

If thewoodseattomy chair is made of particle board and falling apart, can I change it?

Yes. There are twoimportantfactors to adhere to when changing out the wood in a chair seat: First, try to keep the same shape as the original.The chair framewas designedfor this seat to bear and distribute weight.Changing theshape of the seatmay make the chairunsafeto sit in.Second, always use at least3/4-in.thickstock. Anything less may bow and buckle, further compromising the chair.

How do I know if my chair is worthyofbeing reupholstered?

Before yougo through the process of revivinga chair by reupholstering the seat,besure the chair is a viable candidateby checking these few things.

• Solid Frame:Make sure the frame of your chair is solid.That means no creaking when you shift it back and forth and no obvious cracks in the wood.
• No cracks in the gussets:When you look under the chair,you’ll find four smaller pieces of wood, one in each corner angled at 45 degrees.These pieces are often called gussets and keep your chair square and together. If one is cracked or missing, your chair won’t last long, and it is not worth the effort of trying to revive it.
• Unions where the chair frame meets the seat must be solid: If there is a gap where the seat frame meets the chair seat, your chair willhave a high likelihood of fallingapart.A quick nail or screw will probably be unsightly andwon’tkeep the chair together for an extendedperiod of time.All of these factors make the chair not worth a reupholstery job.